February 2007

Noisy neighbors

Leave a Comment / loft / By /

After a long day at the terminal, like today, every so often, like tonight, I get the overwhelming urge to head downstairs to the shop, turn on my noisy dust collector and even noisier bench tools and finish off some project, like the radiator grill for the bedroom reno. However, this being a row house on a quiet block that pretty much blacks out by 10:30pm, I’d get lynched. I even turn off my motorcycle engine and coast the wrong way down the street to my garage rather than rouse the neighbors, and I have street legal pipes on my […]

Loading

Noisy neighbors Read More »

Maybe a roof rack?

Leave a Comment / carpentry, finish carpentry, master bedroom / By /

Not counting the 12 year-old Pontiac wreck I owned for all of four months and on which I managed to put maybe 400 miles before I donated it in disgust to a charity, my 2001 VW Golf is the first car I’ve owned. I’ve been a motorcyclist since I was 18. When I lived in Manhattan, it was all I needed, or wanted. But when I moved to a suburban house with a garage, I had to get four wheels, if only for lumber runs. That’s pretty much all I use it for too. I’ve had the car for six

Loading

Maybe a roof rack? Read More »

Yet another “cool tool” article

Leave a Comment / cabinet making, carpentry, finish carpentry, master bedroom, tools / By /

I’ve blathered a lot on the blog about the coolness of routers but another tool I use quite a bit is a biscuit joiner. What’s that? Bread glue? It’s a tool I first saw TOH demigod, Norm Abrams, use back in the 80s. Okay, let’s be honest: Norm has a shop full of bizarre, narrow purpose tools. But a biscuit (or plate) joiner is really useful, especially for edge-laminating boards as I’m about to do here. It can also be used to strengthen mitered corners or to insert alignment pins. I did the latter when I installed the heavy mahogany

Loading

Yet another “cool tool” article Read More »

Ten gallons of sawdust later…

Leave a Comment / cabinet making, carpentry, finish carpentry, master bedroom / By /

I finished cutting 208 feet of bolection moulding for the wainscotting in the bedroom reno and guess what? I needed 216 feet to complete the job, dammit! I knew I was cutting it close (literally) but I only had a couple of (expensive) red oak 1x8s left which I need for the wainscotting shelf. I’ll dig into my red oak scrap pile and cut the remainder this afternoon. Anyway, I was right. A bolection moulding a/k/a inset panel cap moulding a/k/a rabbeted panel moulding is just an inverted base cap profile with a rabbet. After my router bit quest, I

Loading

Ten gallons of sawdust later… Read More »

Tool Show Post Mortem: The Good, the Bad, the Ugly

Leave a Comment / tools / By /

I’m glad the Somerset Tool Show moved back it to the Exhibit Center because it was suffering at the Ramapo convention center. There were lots of new vendors this year, and lots of new tools. My primary misson however was finding a router bit to cut the bolection mouldings for the wainscotting in my bedroom reno. The router bit yodas I was counting on for enlightenment were no help. One guy even told me I needed a shaper to get that profile. He must have noticed me looking at him like he had two heads because he followed up with,

Loading

Tool Show Post Mortem: The Good, the Bad, the Ugly Read More »

Bay window trim (almost) done.

Leave a Comment / cabinet making, carpentry, finish carpentry, hvac, master bedroom / By /

Sheesh. Another “almost” cop out. The issue here isn’t woodworking but thermodynamics. The steam radiator that Richie from Sessa Plumbing installed is something called an “element”. An element works on the convection principle: as hot air rises off the element, it expands and exits through a grill at the top. This creates a low pressure area underneath which pulls in cold air from the floor through a grill at the bottom. An element radiator usually comes in a butt-ugly metal cabinet. It’s what that missing panel under the middle window needs to replicate. I’m gonna give you a private snapshot

Loading

Bay window trim (almost) done. Read More »

It depends on what “almost” means…

Leave a Comment / carpentry, finish carpentry, master bedroom / By /

I’ve been looking forward to this day for months. Almost all the trim, the doors, cabinets, etc are done! What’s “almost”? By “almost” I mean that the center of operations moves downstairs to my shop. The remainder of the trim work — the cabinet doors and drawers, the panels under the bay window, the stained glass window, the overhead closet doors and even the curved baseboard moulding for the closet corner have to be fabricated. I need my stationary power tools for this stuff. “Almost” also means that I need to make a decision about whether or not to incorporate

Loading

It depends on what “almost” means… Read More »

The Somerset (NJ) Woodworking Show – any NYC area bloggers going?

Leave a Comment / tools / By /

Feb 16-18, 2007 Garden State Exhibit Center 50 Atrium Drive Somerset, NJ (exit 19, Route 287) Sponsored by Wood Magazine This will be like my 8th or 9th visit to this show. It’s like a crack house for woodworking junkies. Every conceivable tool, useful or not, is on display and usually being demonstrated. At least half of my present shop was purchased at one of these shows, including my Delta X Unisaw and Dewalt SCMS. I also load up on all my sandpaper, nitrile gloves and other consumables for the year. The prices are that good. If there’s an answer

Loading

The Somerset (NJ) Woodworking Show – any NYC area bloggers going? Read More »

The Mystery of the Vanishing Paint Brushes

Leave a Comment / carpentry, master bedroom, pets / By /

I thought I was suffering from early dementia. Over the several months of this bedroom renovation I’ve lost a bunch of paint brushes. I’d clean them and stick them… hell, I don’t know where. I just couldn’t find them again. At least four reasonably new paint brushes were missing. What was even stranger is that several paint brushes that I thought I’d stored in my basement shop two flights down were also missing. Just the good ones with the soft bristles. I found them today, laying on the floor at the rear of my new closet. I know I didn’t

Loading

The Mystery of the Vanishing Paint Brushes Read More »

Scroll to Top

Welcome to Brooklyn Row House

This blog is about the challenges of renovating an old (1903) Brooklyn, New York row house.

My last major renovation project was the master bedroom, most of which is about finish carpentry. You’ll find other completed home improvement projects in the Projects submenu at the top of this page.

I’m not a professional builder and don’t pretend to be. I’m just an experienced amateur raised in a family of committed DIYers. I try to closely follow local and national building codes but don’t mistake anything on this site to be professional or even accurate advice! Your mileage may and definitely will vary.

This is the third iteration of BrooklynRowHouse.com, from scratch-built to Drupal and now Wordpress. I hope you enjoy your time here.